These easy to use Z brackets firmly mount your solar modules to any flat surface, yet allow air to flow under the pv module.

• made of anodized aluminum with stainless steel nuts, bolts and washers
• Set includes 4 Z Brackets
• Commonly used for mounting solar modules on boats and RV's.
• Works well with most brand of Solar Panels.
• Suitable for up to 80W

Mount your solar panels without needing to make holes in your roof.

The solar panel side brackets can be used with any aluminium framed solar panel to provide a secure fixing for vehicles, caravans, boats, outbuildings etc. The mounts will support the solar panel at the optimum height above the surface to enable aeration from underneath, ensuring the solar panel functions as efficiently as possible.

Solar panel mounts are an ideal way to fix solar panels on the roof or deck of motor homes and boats. The mounts can be safely bonded to the surface removing the need to drill holes. The mounts also act as a wind deflector and maintain the correct air gap between the solar panel and the roof top / deck.

• Dimensions: 180mm (l) x 65mm (h) . See picture for more details.
• Black ABS plastic
• Full instructions included
• Suitable for aluminium framed solar panels
• Larger panels may require additional corner mounting brackets (product code 08003BS04)
• Recommended bonding agent is Sikaflex 252

Installation: The brackets are first be screwed or bolted to the solar module using suitable stainless steel self-tapping screws. You will need to drill a clearance hole in the ABS brackets at the appropriate recessed ports. Once the brackets are attached to the panel the whole can be bonded to the roof surface using  Sikaflex 252. Full instructions available.

Mount your solar panels without needing to make holes in your roof.

The solar panel corner brackets can be used with any aluminium framed solar panel greater than 15cm in length to provide a secure fixing for vehicles, caravans, boats, outbuildings etc. The solar corner mounts will support the solar panel at the optimum height above the surface to enable aeration from underneath, ensuring the solar panel functions as efficiently as possible.

Depending on the size and weight of the solar module and particularly if fixing the panel to a vehicle, it may be worth considering the addition of a spoiler set for additional support of the long sides of the panel, but for many installations the corner brackets will prove sufficient.

Solar panel mounts are an ideal way to fix solar panels on the roof or deck of motor homes and boats. The mounts can be safely bonded to the surface removing the need to drill holes. The mounts also act as a wind deflector and maintain the correct air gap between the solar panel and the roof top / deck.

• Dimensions: 150mm (w) x 150mm (l) x 65mm (h) . See picture for more details.
• ABS plastic
• Full instructions included
• Suitable for aluminium framed solar panels
• Larger panels may require additional side mounting brackets (product code 08003BS05)
• Black ABS plastic
• Recommended bonding agent is Sikaflex 252

Installation: The brackets are first be screwed or bolted to the solar module using suitable stainless steel self-tapping screws. You will need to drill a clearance hole in the ABS brackets at the appropriate recessed ports. Once the brackets are attached to the panel the whole can be bonded to the roof surface using  Sikaflex 252. Full instructions available.

The Solar Grip is a versatile mounting system that permits a quick temporary or permanent installation of the Sunsei SE-500 without the need for any hand tools.

• Comes with a table mount and a rail mounting system.
• No need to drill your deck or roof
• Fully adjustable ball and socket joint rotates 360 degrees
• Correct installation can increase power generation of the panel by up to 35%.
• Ideal for boats, motorhomes and caravans.

Modules in the PowerFilm Wireless Electronics Series offer a new opportunity to solve the old problems of limited power for wireless electronics in both portable and remote electronic applications.
lightweight, paper thin and durable
flexible enough to curve around an object 3 inches in diameter
will not break if dropped
wide range of sizes and power configurations available
thin profile enables them to be easily integrated with devices for solar recharging or direct power
Ideal for recharging AA, AA, 6V and 2V batteries
Please note: these modules do not have a UV stabilised surface.
Simple to connect - just solder or crimp to the copper tape.

Specifications:

• Power: 0.066W
• Current: 22mA
• Voltage: 3V
• Dimensions (mm): 37 x 64
• Weight (g): 0.7

Durable, ultra-rollable and paper-thin, these amazing marine-grade Powerfilm panels can be fully rolled up. Perfect for applications where extreme flexibility is important, or where a very thin profile is needed.

Mounting:

• Powerfilm panels can be walked on
• Suitable for adhering to a firm surface using a PVA glue
• Fix to canvas awnings,spray hoods & tents or boat/caravan/motorhome roofs with Stayput Fasteners

Features:

• Integrated with a fabric backing for enhanced product functionality these panels perform well in diverse environments, including hot sun.
• Cadmium Free.
• The short integral solar panel cable terminates in a marine grade weatherproof PowerFilm connector
• Provided with two PowerFilm cables - 1m accessory cable (with female cigarette lighter adapter socket) & 4.6m battery cable (with ring terminals) 
• Blocking diodes fitted.
Powerfilm solar panels are monolithically integrated which eliminates the need for damage-prone manual connections of individual solar cells.
• 5 year output warranty.
• Rated 7W, 450mA @ 15.4V
• Dims: 584.2 x 368.3 mm unrolled, 368.3 x 101.6 mm rolled up
• Weight: 0.27 kg

PLEASE NOTE: The 7W Powerfilm panel is part of Powerfilm's new, more powerful range.

Durable, ultra-rollable and paper-thin, these amazing marine-grade Powerfilm panels can be fully rolled up. Perfect for applications where extreme flexibility is important, or where a very thin profile is needed.

Mounting:

• Powerfilm panels can be walked on
• Suitable for adhering to a firm surface using a PVA glue
• Fix to canvas awnings,spray hoods & tents or boat/caravan/motorhome roofs with Stayput Fasteners

Features:

• Integrated with a fabric backing for enhanced product functionality these panels perform well in diverse environments, including hot sun.
• Cadmium Free.
• The short integral solar panel cable terminates in a marine grade weatherproof PowerFilm connector
• Provided with two PowerFilm cables - 1m accessory cable (with female cigarette lighter adapter socket) & 4.6m battery cable (with ring terminals) 
• Blocking diodes fitted.
Powerfilm solar panels are monolithically integrated which eliminates the need for damage-prone manual connections of individual solar cells.
• 5 year output warranty.
•  Rated 28W, 1800mA @ 15.4V
• Dims: 2025.6 x 368.3 mm unrolled, 368.3 x 101.6 mm rolled up
• Weight: 0.82 kg

PLEASE NOTE: The 28W Powerfilm panel is part of Powerfilm's new, more powerful range.

Durable, ultra-rollable and paper-thin, these amazing marine-grade Powerfilm panels can be fully rolled up. Perfect for applications where extreme flexibility is important, or where a very thin profile is needed.

Mounting:

• Powerfilm panels can be walked on
• Suitable for adhering to a firm surface using a PVA glue
• Fix to canvas awnings,spray hoods & tents or boat/caravan/motorhome roofs with Stayput Fasteners

Features:

• Integrated with a fabric backing for enhanced product functionality these panels perform well in diverse environments, including hot sun.
• Cadmium Free.
• The short integral solar panel cable terminates in a marine grade weatherproof PowerFilm connector
• Provided with two PowerFilm cables - 1m accessory cable (with female cigarette lighter adapter socket) & 4.6m battery cable (with ring terminals) 
• Blocking diodes fitted.
Powerfilm solar panels are monolithically integrated which eliminates the need for damage-prone manual connections of individual solar cells.
• 5 year output warranty.
•  Rated 21W, 1350mA @ 15.4V
• Dims: 1543.05 x 368.3 mm unrolled, 368.3 x 101.6 mm rolled up
• Weight: 0.64 kg

PLEASE NOTE: The 21W Powerfilm panel is part of Powerfilm's new, more powerful range.

Durable, ultra-rollable and paper-thin, these amazing marine-grade Powerfilm panels can be fully rolled up. Perfect for applications where extreme flexibility is important, or where a very thin profile is needed.

Mounting:

• Powerfilm panels can be walked on
• Suitable for adhering to a firm surface using a PVA glue
• Fix to canvas awnings,spray hoods & tents or boat/caravan/motorhome roofs with Stayput Fasteners

Features:

• Integrated with a fabric backing for enhanced product functionality these panels perform well in diverse environments, including hot sun.
• Cadmium Free.
• The short integral solar panel cable terminates in a marine grade weatherproof PowerFilm connector
• Provided with two PowerFilm cables - 1m accessory cable (with female cigarette lighter adapter socket) & 4.6m battery cable (with ring terminals) 
• Blocking diodes fitted.
Powerfilm solar panels are monolithically integrated which eliminates the need for damage-prone manual connections of individual solar cells.
• 5 year output warranty.
• Rated 14W, 900mA @ 15.4V
• Dims: 1066.8 x 368.3 mm unrolled, 368.3 x 101.6 mm rolled up
• Weight: 0.445 kg

PLEASE NOTE: The 14W Powerfilm panel is part of Powerfilm's new, more powerful range.

Modules in the PowerFilm Wireless Electronics Series offer a new opportunity to solve the old problems of limited power for wireless electronics in both portable and remote electronic applications.

• lightweight, paper thin and durable
• flexible enough to curve around an object 3 inches in diameter
• will not break if dropped
• thin profile enables them to be easily integrated with devices for solar recharging or direct power
• Ideal for recharging AA, AA, 6V and 2V batteries
• Simple to connect - just solder or crimp to the copper tape.

Specifications:

• Power: 0.36W
• Current: 100mA
• Voltage: 3.6V
• Dimensions (mm): 74 x 150
• Weight (g): 3.1

Please note: these modules do not have a UV stabilised surface.

Inprosolar´s highly durable solar panels can be screwed or glued onto flat surfaces. The panels are backed onto fibreglass, making them lightweight, and are encapsulated within a highly efficient transparent UV resistant polymer. Thin and compact, these solar panels can be walked on with soft shoes. Inprosolar low profile panels also look fantastic and have been widely used for both industrial and recreational purposes.

• 10 year warranty
• fully encapsulated junction box with 1m cable
• suitable for marine applications
• Rated power 0.7A at 16.7V
• Dimensions 45 x 27 x 0.4 cm

This 50W Advanced Solar Panel Charger Controller (also known as a Solar Charge Regulator) uses less than 1/10th the power of the industry average.

The zero battery consumption at night saves lots of power, especially in systems that get covered in snow or need to last through prolonged overcast conditions.

(Almost all other charge regulators have a standby current draw that will drain the battery during poor light conditions).

    * Perfect for telecommunications, solar powered parking meters and other PV systems up to 50W.
    * Save up to 10% of the power from a 5 Watt module.
    * Max Charging current (at 70°C) 4A DC
    * Protection (PV & Battery), against short-circuit & reverse polarity, overload, over temperature & battery removal
    * Can charge a completely discharged battery
    * Extreme design -40 degrees to +70 degrees C
    * Series design (not shunt)
    * Reliable - 100% solid state
    * No radio interference
    * LED indicates charging
    * Wall mountable ABS plastic case
    * Fully encapsulated in epoxy potting
    * Dimensions: 3.8 x 7.0 x 3.1 cm; 50g
    * Battery consumption zero, 0.0 mA
    * Typical solar consumption 5 mA daylight only, 3 mA without LED
    * 5 year warranty

Ultra low consumption version 5mA (during daylight only).  [Consumption is 3mA if no LED is fitted - please call us for details].

For bulk orders we can customise voltage set-points and wire lead lengths.

Global Solar´s P3 Powerpack range of rugged military-style folding panels are small enough to fit in a rucksack, but open up into a powerful portable solar panel for 12V battery charging.. Incorporating solid state, thin-film, PowerFLEX™ solar technology, the P3 provides an excellent choice for situations that require lightweight, durable, silent power. Re-charge batteries, power communication equipment and mobile electronics, plus reduce the battery logistic challenge with the P3. It provides silent energy independence to the user. With no glass to break and easy connectivity these lightweight panels are ideal for expeditions and disaster relief.

• Uses Global Solar´s revolutionary PowerFLEX™ technology, with CIGS solar cells.
• Complete with cable set for full connectivity.
• Works well even under poor light conditions.
• Can be mounted to curved surfaces; built-in grommets.
• Built-in discharge protection.
• Please note, although nominally 12V, these products have an open circuit voltage of up to 30V.
• Charge controller required for standard 12V battery charging — see our P3 solar charge controller for plug-and-play connectivity.
• These panels are now only available in BLACK
• Unfolded dimensions: 1333 x 762 x 2.5 mm
• Folded dimensions: 368 x 216 x 36 mm
• Weight: 1.41 kg
• 1 year warranty.

Global Solar´s P3 Powerpack range of rugged military-style folding panels are small enough to fit in a rucksack, but open up into a powerful portable solar panel for 12V battery charging.. Incorporating solid state, thin-film, PowerFLEX™ solar technology, the P3 provides an excellent choice for situations that require lightweight, durable, silent power. Re-charge batteries, power communication equipment and mobile electronics, plus reduce the battery logistic challenge with the P3. It provides silent energy independence to the user. With no glass to break and easy connectivity these lightweight panels are ideal for expeditions and disaster relief.

• Uses Global Solar´s revolutionary PowerFLEX™ technology, with CIGS solar cells.
• Complete with cable set for full connectivity.
• Works well even under poor light conditions.
• Can be mounted to curved surfaces; built-in grommets.
• Built-in discharge protection.
• Please note, although nominally 12V, these products have an open circuit voltage of up to 30V.
• Charge controller required for standard 12V battery charging — see our P3 controller for plug-and-play connectivity.
• These panels are now only available in BLACK
• Unfolded dimensions: 1118 x 553 x 2.5 mm
• Folded dimensions: 257 x 216 x 30.5 mm
• Weight: 1.1 kg
• 1 year warranty.

The especially rugged construction of these PowerFilm modules makes them ideal for hobby or OEM application where the panel is permanently outdoors and exposed to the elements

• UV stabilised surface with extra edge seal for weather production
• tin-coated copper leads extend from the module.
• Coating the leads with an RTV silicon compound can provide a tightly sealed package.
• lightweight, thin and durable
• flexible enough to curve around an object 3 inches in diameter
• will not break if dropped
• range of sizes and power configurations available
• thin profile enables them to be easily integrated with devices for solar recharging or direct power
• Ideal for recharging AA, AA 6V and 2V batteries
• Simple to connect - just solder or crimp to the copper tape

Specifications:

• Power: 1.54W
• Current: 100mA
• Voltage: 15.4V
• Dimensions (mm): 270 x 175 (This is for the protective laminate. The panel sealed inside is slightly smaller)
• Weight (g):56.4

UV Qualities:

To protect the panel from the weather and UV, the module is encapsulated in ETFE/TPU. 

• ETFE passes more than 90% of the UV light therefore is almost UV inert.
• TPU blocks the UV light around 400nm and is UV resistant. 

With this UV resistant TPU layer, the panel’s lifetime is double to triple the standard few years it would have unprotected.

The especially rugged construction of these PowerFilm modules makes them ideal for hobby or OEM application where the panel is permanently outdoors and exposed to the elements

• UV stabilised surface with extra edge seal for weather production
• tin-coated copper leads extend from the module.
• Coating the leads with an RTV silicon compound can provide a tightly sealed package.
• lightweight, thin and durable
• flexible enough to curve around an object 3 inches in diameter
• will not break if dropped
• range of sizes and power configurations available
• thin profile enables them to be easily integrated with devices for solar recharging or direct power
• Ideal for recharging AA, AA 6V and 2V batteries
• Simple to connect - just solder or crimp to the copper tape

Specifications:

• Power: 1.44W
• Current: 200mA
• Voltage: 7.2V
• Dimensions (mm): 270 x 175 (This is for the protective laminate. The panel sealed inside is slightly smaller).
• Weight (g): 54.9

UV Qualities:

To protect the panel from the weather and UV, the module is encapsulated in ETFE/TPU. 

• ETFE passes more than 90% of the UV light therefore is almost UV inert.
• TPU blocks the UV light around 400nm and is UV resistant. 

With this UV resistant TPU layer, the panel’s lifetime is double to triple the standard few years it would have unprotected.

Modules in the PowerFilm Wireless Electronics Series offer a new opportunity to solve the old problems of limited power for wireless electronics in both portable and remote electronic applications.
lightweight, paper thin and durable
flexible enough to curve around an object 3 inches in diameter
will not break if dropped
wide range of sizes and power configurations available
thin profile enables them to be easily integrated with devices for solar recharging or direct power
Ideal for recharging AA, AA, 6V and 2V batteries
Please note: these modules do not have a UV stabilised surface.
Simple to connect - just solder or crimp to the copper tape.

Specifications:

• Power: 1.44W
• Current: 200mA
• Voltage: 7.2V
• Dimensions (mm): 253 x 150
• Weight (g): 25.9 

This mini solar module is designed to be easily integrated within remote controlled aircraft.

• Rated 100mA @ 7.2V
• measures 270x90mm, and just 0.2mm thick
• very lightweight (7.6g )
• lightweight, paper thin and durable
• flexible enough to curve around an object 3 inches in diameter
• will not break if dropped
• extra edge seal for weather production and adhesion
• comes with a strong pressure sensitive adhesive for simple bonding.
• these modules do not have UV stabilised surface.
• for connection just solder or crimp to the copper tape on the back of the module.

Specifications:

• Current: 100mA
• Power: 0.72W
• Voltage: 7.2V
• Dimensions (mm): 270 x 90
• Weight (g): 5.9

A small, low-voltage encapsulated PV cell suitable for a variety of educational or hobby uses. The easy-to-use screw terminals make this module ideal for use in school and college experiments.

• Rated 0.5W, 200mA@2.5V
• Monocrystalline
• Encapsulated in clear acrylic
• Integrated stand with screw terminals
• Dimensions 67 x 125 x 50 mm.

For other projects, we also have solar cells under 4v and solar cells from 6v to 15.4v

Modules in the PowerFilm Wireless Electronics Series offer a new opportunity to solve the old problems of limited power for wireless electronics in both portable and remote electronic applications.
lightweight, paper thin and durable
flexible enough to curve around an object 3 inches in diameter
will not break if dropped
wide range of sizes and power configurations available
thin profile enables them to be easily integrated with devices for solar recharging or direct power
Ideal for recharging AA, AA, 6V and 2V batteries
Please note: these modules do not have a UV stabilised surface.
Simple to connect - just solder or crimp to the copper tape.

Specifications:

• Dimensions (mm): 150 x 114
• Weight (g): 4.6
• Voltage: 6V
• Current: 100mA
• Power: 0.6W

The especially rugged construction of these PowerFilm modules makes them ideal for hobby or OEM application where the panel is permanently outdoors and exposed to the elements

• UV stabilised surface with extra edge seal for weather production
• tin-coated copper leads extend from the module.
• Coating the leads with an RTV silicon compound can provide a tightly sealed package.
• lightweight, thin and durable
• flexible enough to curve around an object 3 inches in diameter
• will not break if dropped
• range of sizes and power configurations available
• thin profile enables them to be easily integrated with devices for solar recharging or direct power
• Ideal for recharging AA, AA 6V and 2V batteries
• Simple to connect - just solder or crimp to the copper tape (see the video for more details)

Specifications:

• Current: 50mA
• Voltage: 15.4V
• Power: 0.77W
• Dimensions (mm): 270 x 100 (This is the size of the protective laminate. The panel sealed inside is slightly smaller).
• Weight (g): 31.8g

UV Qualities:

To protect the panel from the weather and UV, the module is encapsulated in ETFE/TPU. 

• ETFE passes more than 90% of the UV light therefore is almost UV inert.
• TPU blocks the UV light around 400nm and is UV resistant. 

With this UV resistant TPU layer, the panel’s lifetime is double to triple the standard few years it would have unprotected.